Instructions

User Instructions

A. Top Stone: Salt dispensing nozzle

B. Middle Stone: Salt fill (small forward-facing hole, closest to dispensing nozzle)

C. Bottom Stone: Salt grinder. Power buttons 5 mins, strongest concentration; 10 minutes medium concentration; 15 minutes lowest concentration; Battery indicator; Light strip time indicator; Power adaptor port

D. Cradle: Base supports the devices range of tilt angles

Plug Wall Adaptor into the Power Adapter Port.
Charge device for at least 6 hours.

Device will not work when plugged in.
Unplug from Wall Adapter to use.

Lift and remove top stone. It is attached by magnets.

Pour one (1) salt sachet into fill (small hole closest to dispensing nozzle). May use funnel, if desired. Replace top stone.

Alternative method: remove top stone first then middle stone and pour directly into the grinding chamber. Replace both stones.

If using your own halogenerator-specific salt, measure ¼ to ½ teaspoon.

Select run time. Adjust device on the cradle to direct the dispensing nozzle toward your nose and mouth. Breathe deeply and intentionally through your nose.

Clean thoroughly after each use. There will be residual salt left in the grinding chamber and on the underside of the middle rock, in particular. This is normal.

Unplug from wall to clean. Use provided cleaning brush.

Remove top stone and gently brush off any remaining salt.

Remove middle stone and gently brush off any remaining salt.

Remove bottom stone from the cradle and gently brush off remaining salt from the grinding chamber.

Remove grinder blade by gently lifting it. Brush clean and replace the blade.

Remove as much salt residue as possible.
Re-assemble for next use.

Do not use water to clean the device. The device is not water-proof. Washing or rinsing with water or using in high humidity environments will damage the product and the salt.

The dry salt aerosol that’s dispensed from the nozzle is very fine and not typically visible.

Place charged Salt Stone on stable surface.
Fill grinding chamber with halogenerator-specific salt in specified amounts.
Adjust dispensing nozzle toward nose and mouth
Push any button to wake the device up. All button LEDs blink.
Select the mode button (session time) you desire. Press to start.
   •   When a mode (session time) is selected, only the LED of the selected mode is illuminated.
   •   Single press the selected mode button to pause the session.
   •   Long press the selected mode button to cancel the session.
Brush clean of residual salt after use to ensure optimal performance.

For indoor use only, in low air-flow environments
Keep out of reach of children and pets
Do not clean with water
Do not submerge in water or expose to high humidity conditions
Do not block air intake grill
Not intended to diagnose, treat, cure, or prevent any disease

Dispose of Salt Stone responsibly in accordance with your local regulations to help protect the environment.

Product Specifications

Overview:
3 “stones” stacked on top of a base (cradle), retained together via magnets.

1. Top Stone:
Houses the nozzle assembly and upper air path. Ground salt is dispensed from here.

2. Middle Stone:
Contains the air inlets, salt inlet, funnel, middle air path, and upper grind chamber

3. Bottom Stone:
Houses electronic components

4. Cradle:
Contains a magnet that supports the device’s range of tilt angles.

Directs and streamlines the dry salt aerosol. Ideal user position is facing dispensing nozzle, at approximately 15 inches away for optimal effect.

Via Middle Rock: Lift and pour salt dosage directly into the grind chamber.

Via Top Rock: Lift and pour salt dose into the first, most forward inlet hole. May use funnel.

Device’s angle can be adjusted (-45° to 45°) to accommodate different use cases. Angles are retained via magnets positioned in the product base and bottom rock.

Button Selectors

3 buttons to indicate 3 modes:
Low (15 minute)
Medium (10 minute)
High (5 minute)
Push any button to wake the device up. All button LEDs blink.
When a mode is selected, only the LED of the selected mode blinks, and continues throughout the selected session until session completion.
Single press the selected mode button to pause the session.
Long press the selected mode button to cancel the session.

The light bar fully illuminates when any session begins. The number of LEDs illuminating the bar gradually decreases (LEDs turn off successively in the direction the nozzle points) until the session is over.

The charging port is located in the rear of the bottom rock.

Charging: LED on; blinking red.

Fully charged: LED on; solid green.